Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL GTX™ Resin GTX850 - (PPE+PA*)-GF50 - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for NORYL GTX™ Resin GTX850:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Noryl GTX datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 기계적 특성 - 열적 특성 - 기타 특성 - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
제품 설명서
NORYL GTX850 resin is a 50% glass reinforced alloy of Polyphenylene Ether (PPE) + Polyamide (PA). This injection moldable grade has high stiffness (flexural modulus 15.2 GPa), excellent chemical resistance, and high heat resistance. Target application of GTX850 is a wide variety of automotive under-the-hood, water management and consumer electronics structural applications.
Processing/Physical Characteristics값단위시험규격
ASTM 데이터
성형 수축률, 평행 0.0035 mm/mm ASTM D 955
성형 수축률, 수직 0.004 mm/mm ASTM D 955
기계적 특성값단위시험규격
ISO 데이터
인장탄성률 17000 MPa ISO 527
파단시 강도 226 MPa ISO 527
파단시 신율 3.3 % ISO 527
굴곡 계수, 23°C 14800 MPa ISO 178
굴곡 강도 365 MPa ISO 178
아이조드 충격은 노치, +23°C 12.5 kJ/m² ISO 180/1A
ASTM 데이터
인장탄성률 17500 MPa ASTM D 638
파단시 강도 232 MPa ASTM D 638
파단시 신율 3.6 % ASTM D 638
굴곡 계수 15200 MPa ASTM D 790
굴곡 강도 370 MPa ASTM D 790
아이조드 충격은 노치, 1/8 in 128 J/m ASTM D 256
Izod충격강도, 1/8 in 1200 J/m ASTM D 256
열적 특성값단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 250 °C ISO 75-1/-2
ASTM 데이터
DTUL @ 264 psi 251 °C ASTM D 648
기타 특성값단위시험규격
물에서의 흡수성, 24hr 0.16 % ASTM D 570
밀도 1570 kg/m³ ASTM D 792
Processing Recommendation Injection Molding값단위시험규격
Pre-drying - Temperature 95 - 105 °C -
Pre-drying - Time 3 - 4 h -
Processing humidity ≤0.02 % -
용융수지온도 280 - 305 °C -
성형온도 75 - 120 °C -
Zone 1 265 - 305 °C -
Zone 2 270 - 305 °C -
Zone 3 275 - 305 °C -
Nozzle temperature 280 - 305 °C -
Screw speed 20 - 100 rpm -
Back pressure 0.3 - 1.4 MPa -
특징
생산 공정
사출 성형
특별 특성
열안정성
내화학성에
General Chemical Resistance
응용
자동차의, 전기 및 전자
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧, 쨀짼쨘횓 쨔횞 횁횩쩐횙 쩐횈쨍횧쨍짰횆짬
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.